8
mar
How to program the Wiśniowski gate remote control
How to program the Wiśniowski Python gate remote control, 2k310, PIC310, 2k433, 4k433, 2kST, 2kST (Wiking), 4k433, 4A433, 4GO
| Procedure for coding transmitters into the eS1 controller: | ||
|
On the eS1 controller, press the "UCZ" button and hold it
for approx. 2 sec. until audible 3s
relay clicks or visible flashes
signal lamp. Then press (approx. 2
sec.) button of the transmitter you want to program,
wait for confirmation of encoding
by tapping the relay 3 times or flashing
signal lamp. If they were not heard
clicking or no lamp flashing, procedure
coding needs to be repeated.
NOTE: model withdrawn from sale - since 2007, we use a navy blue transmitter with a red diode as a replacement (see below).
|
PYTHON
• fixed code 310 MHz
• black housing,
• yellow buttons.
|
|
| Copying transmitters | ||
|
In the new transmitter, press the selected key
and hold until the transmitter LED stops blinking
and it will glow continuously. Holding
continue to hold the button of the new transmitter close to it
original transmitter (whose code you want to duplicate)
so that they touch the front part of the housing
and press its selected button. In the teaching transmitter
code, the LED will start flashing and then
will go off. This means remembering the code correctly.
Each button requires separate learning.
|
2k310 transmitter
• catalog number 90241
• navy blue housing,
• red LED.
|
|
| Procedure for coding transmitters for controllers: eL1Q, eL6Q, eL7Q, eL16Q | ||
|
We encode each transmitter of this type individually
to the controller – see the User Manual
and Assembly. Please find it on the controller board
"UCZ" button. Press it and hold it until
the LED on the board will turn off. Over the next few years
10 seconds by briefly pressing the selected one
button of the new transmitter can be entered
transmitter code to the controller memory. Triple
LED blinking means that the coding has been completed
completed correctly. Every button requires
separate teaching.
|
2k433 transmitter
• catalog number: 10646,
• gray housing,
• white LED
4k433 transmitter
• catalog number: 10647,
• gray housing,
• white LED.
|
|
| Procedure for coding transmitters for ST-1 and ST-2 controllers: | ||
|
ST–1 A, B, C (black housing), ST–1 D (gray housing), ST–2 (red and black housing) We encode each transmitter of this type individually
to the controller – see the Operation and Installation Manual:
• enter the controller into programming mode
by entering the installer code (default setting: 1234)
and press "CONFIRM" or "OK",
• use the +/– keys to select "Pr" mode and confirm
press the "CONFIRM" or "OK" button,
• then use the +/– buttons to select the cell number
memory where the code is to be saved
transmitter (the selected cell number will flash),
• press the selected button of the new transmitter
and hold it until the cell number stops
blink and become solid.
This means that the encoding is complete
correct. By pressing the button repeatedly
"CANCEL" return to normal operation mode
controller.
Each key requires separate learning.
|
2kST transmitter
• catalog number: 90390,
• gray housing,
• red LED.
2kST transmitter – old guy
• withdrawn from sale,
the so-called Viking.
4k433 transmitter
• catalog number: 90391,
• gray housing,
• red LED.
|
|
| Procedure for coding transmitters into the eL3Q controller | ||
|
Press the "UCZ" key (the LED will turn off) and release. Now within 10 sec. press the selected transmitter button (approx. 1 sec.). Code adoption
to the controller memory will be confirmed by the LED blinking three times. We code each remote control individually by repeating the procedure
|
||
| Universal transmitter for 433MHz controllers: eL1Q, eL3Q, eL6Q, eL7Q, eL16Q, eL20Q, eL4000, ST–1, ST–2 | ||
|
We encode each transmitter of this type individually
to the controller – see the Operation and Installation manual
for eL or ST series controllers.
|
4A433 MHz transmitter
• catalog number 91492,
• silver and black housing
with protection
buttons.
Button programming:
button A – ST 1, ST 2, entire gate
button B – ST 2 entire gate
button C – ST 2 gate
D button – ST 2 gate
4GO transmitter
• catalog number 93532.
Button programming:
button A – ST 1, ST 2, entire gate
button B – ST 2 entire gate
button C – ST 2 gate
D button – ST 2 gate
COVER transmitter
• catalog number 94687 (white)
• catalog number 9670 (black)
Button programming:
button A – ST 1, ST 2, entire gate
button B – ST 2 entire gate
button C – ST 2 gate
D button – ST 2 gate
|
Programming Wiśniowski Python remote controls, 2k310, PIC310, 2k433, 4k433, 2kST, 2kST (Wiking), 4k433, 4A433, 4GO. Find out how to program the Wiśniowski gate remote control. It's easy when you know how to properly program Wiśniowski remote controls. The process is similar for most models.
Share:
